Перейти к содержанию

Recommended Posts

Crown Victoria P71 95'

 

Вот думаю от нечего делать поменять масло в мосту. 

Мануаль я конечно прочёл, но сталось неясным, каков объём масла необходим для замены?

 

Поделитесь опытом и нюансами если кто менял.

Ссылка на комментарий
Share on other sites

1992-2002: ~ 1.774 L (3.75 pints)

Типа масла: 80w90 (75w90)

Для лимузинов и полиции: 75w140

Благодарю за информацию! 

О процессе и проделанных работах отпишусь сюда.

Ссылка на комментарий
Share on other sites

Crown Victoria P71 95'

 

Вот думаю от нечего делать поменять масло в мосту. 

Мануаль я конечно прочёл, но сталось неясным, каков объём масла необходим для замены?

 

Поделитесь опытом и нюансами если кто менял.

Section 05-00: Axle and Driveshaft — Service
1995 Town Car/Crown Victoria/Grand Marquis Workshop Manual
SPECIFICATIONS
Specifications AXLE SHAFT ENDPLAY Description mm Inch Axle Shaft Endplay (Max.) 0.762 0.030

 

 

LUBRICANT CAPACITIES Description Liters Pints Premium Rear Axle Lubricant XY-80W90-QL or -KL or equivalent meeting Ford specification WSP-M2C197-A 1.7 3.75 Friction Modifier — F3TZ-19B546-MA (WSP-M2C196-A) 0.118 .25

 

 

DRIVE PINION BEARING PRELOAD Description Nm Lb-In Minimum Torque Required to Tighten Pinion Flange Nut to Obtain Correct Pinion Bearing Preload 190a 140 (Lb-Ft) Pinion Bearing Preload — (Collapsible Spacer) Used Bearingsb 0.9-1.5 8-14 New Bearings 1.8-3.2 16-29
a If pinion bearing preload exceeds specification before this torque is obtained, install a new collapsible spacer. 

b With oil seal. 

 

 

RING GEAR BACKLASH Description mm Inches Backlash Between Ring Gear and Pinion Teeth .203-.4 .008-.015 Maximum Backlash Variation Between Teeth .1016 .004

 

 

RING GEAR RUNOUT Description mm Inches Maximum Runout of Backface of Ring Gear .0762 .004

 

 

TORQUE SPECIFICATIONS Description N-m Lb-Ft Driveshaft to Rear Axle U-Joint Flange Bolts 95-130 70-95 Differential Side Bearing Cap Bolts 95-115 70-85 Pinion Nut 217 160 Axle Housing Cover Retaining Bolts 38-52 28-38 Filler Plug 20-41 15-30

 

 

Ссылка на комментарий
Share on other sites

1992-2002: ~ 1.774 L (3.75 pints)

Типа масла: 80w90 (75w90)

Для лимузинов и полиции: 75w140

про лимузины и полицию ничего не сказано.обязателен модификатор трения

 

Section 05-00: Axle and Driveshaft — Service
1995 Town Car/Crown Victoria/Grand Marquis Workshop Manual
LUBRICATION
Draining and Filling

8.8-Inch Axle

  1. Raise vehicle. Refer to Section 00-02.
  1. Clean all dirt from area of axle housing cover (4033) .
  1. Drain rear axle lubricant by removing axle housing cover .

Filling

  1. ani_caut.gif CAUTION: Make sure machined surfaces on both axle housing cover and rear axle housing (4010) are clean before installing the new silicone sealant. Inside of rear axle housing must be covered when cleaning the machined surface to prevent axle contamination. Tighten the axle housing cover bolts (4346) in a crosswise pattern to ensure uniform draw on cover.

    NOTE: Axle housing cover assembly must be installed within 15 minutes of the silicone rubber application or new silicone rubber must be applied.

    Apply Silicone Rubber D6AZ-19562-AA or -BA or equivalent meeting Ford specification ESB-M4G92-A or WSE-M4G323-A1. Install axle housing cover and tighten axle housing cover bolts to 38-52 Nm (28-38 lb-ft). 

     

    F2667H.gif

     

  1. Add Motorcraft Premium Rear Axle Lubricant XY-80W90-QL or -KL or equivalent meeting Ford specification WSP-M2C197-A until it is 6-14 mm (0.250-0.562 inch) below bottom of fill hole. Add 118 ml (2 oz) of Ford Additive Friction Modifier F3TZ-19B546-MA or equivalent meeting Ford specification WSP-M2C196-A to Traction-Lok axles. Install fill plug and tighten to 20-41 Nm (15-30 lb-ft).
Ссылка на комментарий
Share on other sites

Это если мост с блокировкой

это, даже,если он без блокировки))) 

с блокировкой,рассматривается отдельно.

 

Section 05-02B: Differential, Traction-Lok Limited Slip — 8.8-Inch Ring Gear
1995 Town Car/Crown Victoria/Grand Marquis Workshop Manual
SPECIFICATIONS
Specifications LUBRICANT CAPACITYa Description Liters Pints Rear Axle Lubricant — Premium Rear Axle Lubricant XY-80W90-QL or -KL or equivalent meeting Ford specification WSA-M2C197-A 1.8 3.75 Additive Friction Modifier — F3TZ-19B546-MA 

WSP-M2C196-A 0.059 0.125

a Refer to Section 05-02A for fill procedures.

 

 

BACKLASH BETWEEN RING GEAR AND PINION Description mm Inches Backlash Between Ring Gear and Pinion Teeth .203-.040 .008-.015 Maximum Backlash Variation Between Teeth .010 .004

 

 

TORQUE SPECIFICATIONS Description N-m Lb-Ft Oil Filler Plug 20-41 15-30 Ring Gear Retaining Bolts 95-115 70-85 Axle Housing Cover Bolts 34-47 25-35 Clutch Pack Gauge 6.7 60 (Lb-In)
Ссылка на комментарий
Share on other sites

Присоединяйтесь к обсуждению

Вы можете написать сейчас и зарегистрироваться позже. Если у вас есть аккаунт, авторизуйтесь, чтобы опубликовать от имени своего аккаунта.

Гость
Reply to this topic...

×   Вставлено с форматированием.   Вставить как обычный текст

  Разрешено использовать не более 75 эмодзи.

×   Ваша ссылка была автоматически встроена.   Отображать как обычную ссылку

×   Ваш предыдущий контент был восстановлен.   Очистить редактор

×   Вы не можете вставлять изображения напрямую. Загружайте или вставляйте изображения по ссылке.

Загрузка...
×
×
  • Создать...